12 Facts About Car Ignition Lock To Make You Look Smart Around The Cooler Water Cooler > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Why is My Car Ignition Locked?

There are a variety of reasons the ignition of your car could be locked. One reason is that the key is dirty or has a damaged wafer inside. You can fix this by sliding the key in and out of the cylinder many times.

Another possibility is that the pins inside the lock cylinder are stuck. You could tap the cylinder lightly using a small tack-hammer.

Check the Battery

The shifter switch on the transmission may be malfunctioning when the car ignition switch replacement is in Park, neutral or won't start when the key is turned on. This can be easily repaired by moving the shifter up or down to get the car into gear.

If it is still not turning, the problem could be due to the neutral safety switch or the transmission shifter cable. These can be easily fixed by a mechanic or by a local locksmith for cars.

The ignition cylinder can also be worn out. Over time, the ignition and the key may wear out, which causes them to become difficult to insert or remove. A lubricant, like silicon lock lubricant, could solve this issue by allowing the wafers to slide into the place.

The key could get clogged by lint from your pockets and adhesive from tape used to secure packages. This prevents the key from sliding into the ignition. To resolve this issue try cleaning the key with a cloth or using a cleaner, like Triflow. You could also try a spare key to determine if the issue is the ignition and key replacement or the key.

When the key is in the ignition you can tap it with a small piece of hammer. This will create a slight vibration that might cause enough friction to loosen the wafers inside the ignition and allow them to slide in place. Be careful not to scratch the ignition cylinder or key.

If none of the above work, you should contact a locksmith to test it out. It could be that the key is damaged in the ignition, or it may be time to replace the whole thing. Locksmiths can create an alternative key if the issue is the key. If the ignition cylinder is the cause then you'll need to take your car to a repair shop for it to be replaced. These issues are generally simple to repair.

Check the steering wheel

A simple problem that can prevent the ignition from turning is a locked steering wheel. It could happen if an individual driver is unintentionally engaged with the steering wheel while they exit or get into the vehicle. This is typically caused by yanking the wheel and resting it against their body. It can also happen if an individual in the rear seat accidentally engages the brakes as they exit the vehicle.

This is a simple solution that doesn't require going to the mechanic or locksmith. First, check that the gear shift is either in neutral or Park. If it's not, gently push or pull the gear shifter until it shifts to one of these positions. Also, you should activate the handbrake or press the brake prior to turning the key.

If the wheel isn't locked, a quick inspection of the steering column will determine if the key is connected to the lock cylinder. This is usually identified by a small "Lock" label in the lower area of the ignition circle. It is possible to disengage the lock by gently jiggling the key or pulling it down with moderate force. It is essential not to apply too much force as this could damage the key or even cut off a wafer within the lock cylinder.

Another thing to try is using an additional key to determine whether it is able to disengage the lock. This could indicate that the key is worn and no longer able engage the wafers within the lock cylinder. If this is the situation the locksmith at Karl Chevrolet Webster City will be able to design an alternative key.

If the key doesn't engage after spraying penetrating lubricant, it might help. Simply spray a tiny amount around the ignition, and keyhole, then gently tap or jiggle it until it starts to engage. If this doesn't work, you may need to consult a specialist in your local dealership for cars. They will be able to provide you with a replacement key, and will also replace the ignition cylinder, if necessary.

Check the Key

If you are unable get your key to turn the ignition, it's likely that there is something wrong with your key. You can clean any foreign material (lint from packing tape or adhesive) from the key. It is also possible to rub alcohol or Goo Gone on the key to see if it helps.

If the pins in the lock aren't moving in a proper manner when you insert your key, it is possible that they are stuck. If you have a spare key to test, put it into the ignition and gently pulling it out. You should be able to hear and feel the pins move inside. If you don't feel any movement, you could grease them with graphite. You can buy graphite in small tubes which can be sprinkled into the keyhole. This will assist the pins slide into place as you insert the key and stop them from becoming stuck.

A more serious issue with your key could be that it has worn or damaged, making it unable to connect the internal pins inside the ignition cylinder. This could cause the ignition cylinder to not turn and prevent you from starting your car. If this is the case you'll need to bring your car to repair or locksmith shop for service.

If you're able to turn your car ignition lock on with a spare key and you have ruled out any issues with the battery or steering wheel it could be that the ignition cylinder has worn out. You can try to loosen the lock cylinder using the sharp end of a screwdriver, or the handle of the Hammer (not the head). Sometimes, a gentle tap on the cylinder can free it to allow you to turn the key of your car. If this doesn't work then you'll need your lock's cylinder replaced by a mechanic.

Check the Ignition Socket

The ignition socket is the place your key slides into and out of position when it is inserted. Most of the time, it gets gunked up with debris or as due to wear and wear and tear. Try putting some silicon lock lubricant (like WD-40) into the ignition to help things move along.

You can also use a small hammer, and tap gently on the inside of the ignition to loosen or reset the pins that are out of alignment. Be cautious not to overdo it or you may cause serious damage to the ignition switch.

Before you do this, ensure that your car's gearbox is either in park or neutral. A lot of newer vehicles come with a system which locks the steering wheel when it is not in neutral or park. This can prevent the ignition key from turning.

If you have done all of this and still not able to get your key to turn, it is likely that the housing of your ignition cylinder is in need of replacement. It is important to remember that different vehicles require different procedures for replacing the ignition cylinder.

Generally speaking, this involves taking off the plastic cover that covers the steering column and ignition assembly. To remove it, you'll need adjust the tilt-wheel to its lowest position. Then, loosen any fasteners that hold it in place.

After you have removed the cover, you'll have to remove the old ignition cylinder from the steering column. It is then essential to check the new one that you have purchased with the original one to make sure they are an identical match. After this you can then install the new ignition cylinder the same way that you did with the old one.

It is possible that, despite our best efforts, the ignition can be damaged and require to be replaced. It is recommended that if this happens you contact an Tempe Locksmith. A locksmith can assist you in selecting the right replacement and install it properly to ensure that your vehicle will be able to start up again.